loading

How to Read a Cable Assembly Bend Test Report

×
How to Read a Cable Assembly Bend Test Report

MOCO Connectors / Custom Cable Assemblies

What Should Buyers Look for in a Custom Cable Assembly Bend Test Report?

A bend test report may say that a cable assembly completed the required cycles and passed. Before accepting the report, check which end was tested, how the sample was bent, and what counted as a pass.

Start with three things: the tested sample configuration, the test conditions, and the acceptance criteria. Together, they show whether the report covers the requirements for your order.

1. Match the report to the assembly and the tested end

Check the cable assembly part number, drawing revision, and sample ID. If the two ends use different connectors, boots, or overmolds, confirm whether the report covers End A, End B, or both ends tested separately.

For example, if the cable flexes at the exit of End B in the equipment and the report covers End A, ask whether a separate End B record exists or whether another test is needed. If the cable, boot, or exit geometry changes, confirm whether the existing evidence covers the revised configuration.

Cable assembly with the End B cable exit highlighted A generic assembly has a straight connector on the left and a different connector and boot on the right. The End B cable exit is circled. Cable exit under review End A End B
Figure 1. Identify the cable exit that moves in service and match it to the tested end.

2. Read the cycle count alongside the test conditions

Two tests can run for the same number of cycles while applying different loads or bending the cable at different angles. Check the conditions in the report or in the test plan referenced by the report.

Report field What to check
Test location and fixture Which end was fixed and where the cable bent.
Bend angle and load How the angle was defined, what load was applied, and where it was applied.
Speed and cycle count Test speed, how one cycle was counted, and the target and actual cycle counts.
Sample quantity How many samples were tested and whether individual results are available.
Stop condition Whether the test stopped at the target count or ended early after a failure or other event.
Illustrative bend test fixture with a suspended load The fixture holds the sample near its connector. Dashed lines indicate alternate cable positions, and a weight shows where the load acts. FixtureTested endBend angleApplied load
Figure 2. A typical report identifies the fixed end, bend angle, and applied load. Setup shown for illustration.

If the assembly moves at a joint, pivot arm, or reciprocating mechanism, share the mounting points, direction of motion, and available space with the supplier. Those details help both teams decide whether the proposed setup covers the area of concern and whether testing in the equipment is also needed.

3. Check how the sample passed

Post-test continuity shows whether the checked circuits are connected at the end of the test. Monitoring during bending can detect interruptions as the cable moves. The shortest detectable interruption depends on the monitoring setup and the agreed threshold.

If brief interruptions matter, specify which circuits to monitor, how they will be monitored, and what duration counts as a failure. If the project also calls for checking jacket cracks, a loose boot, or overmold damage, list those as separate post-test visual checks.

A pull test report can complement the bend test report. Review its loading method and the part of the assembly being pulled to see which requirement it addresses.

Illustrative timeline comparing monitoring during bending with a post-test continuity check A brief interruption occurs during bending. A later continuity check shows a connected circuit at the end. Monitoring during bending Brief interruption Post-test check Circuit connected
Figure 3. A circuit can be connected at the final check even if it briefly opened during bending. Illustrative trace.

4. Decide whether the report supports acceptance

Compare the report with the agreed requirements. A missing revision may call for a corrected record. A gap in the tested end, load, or monitoring method may require additional evidence or a new test.

Example acceptance review
Project requirement Report shows Next step
Verify the moving End B End A tested Check for a separate End B record and agree whether to test End B.
Monitor specified signal circuits during bending Post-test continuity recorded Ask for in-test monitoring records and confirm the interruption criterion.
Verify the current drawing revision Part number listed, revision missing Ask the supplier to link the tested sample ID to its drawing revision.

Frequently asked questions

Can the cycle count predict service life?

The report shows how the tested samples performed under the recorded conditions. Estimating service life also requires information about the actual mounting, motion, load, and environment, and how those conditions relate to the test.

Do we need a bend test if continuity has already been checked?

That depends on the application and the acceptance requirements. If the cable flexes repeatedly in service, agree where it should bend, under what load, for how many cycles, and which electrical checks apply.

Discuss Your Cable Assembly Bend Test with MOCO

Need to check whether a bend test report covers your application? Send us: sales5@mocosz.com

  • Your assembly part number and drawing revision, or a description of the configuration
  • Which end flexes and how the cable is mounted in your equipment
  • Any agreed test conditions and pass criteria, plus the existing report if available

MOCO can help you identify what the report covers and what still needs to be verified.

prev
5 Tips for Replacing Connectors in Cable Assemblies
How Quadruped Robot Interfaces Balance Waterproofing, Vibration Resistance and Fast Maintenance
next
recommended for you
Get in touch with us

 Shenzhen MOCO Interconnect Co., Ltd. 

Become a world-class industrial connector supplier & manufacturer in China, MOCO Connectors providing reliable and convenient connector solutions for global customers

If you have any question, please contact MOCO connectors.

TEL: +86 -134 1096 6347

WhatsApp: 86-13686431391

EMAIL: eric@mocosz.com


2/F 1st Block,XinHao Industrial Park,N.O 21 XinWei Rd,XinZhuang Community,MaTian, GuangMing District,Shenzhen,P.R.C

Copyright © 2026  Shenzhen MOCO Interconnect Co., Ltd.  | Sitemap   |  Privacy Policy
Customer service